تعتبر البراغي الكروية أكثر مكونات النقل شيوعًا في أدوات الآلات والآلات الدقيقة. وتتمثل وظيفتها الرئيسية في تحويل الحركة الدورانية إلى حركة خطية ، أو تحويل عزم الدوران إلى قوة تكرارية محورية. في الوقت نفسه ، تتميز أيضًا بخصائص الدقة العالية والقابلية للانعكاس والكفاءة العالية.
الانحراف اللامركزي: يشير إلى الانحراف المركزي بين الجانب الثابت والجانب الداعم.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60m / min ، ويمكن اعتبار تزييت ضباب الزيت القسري 60-100 م / دقيقة. يوصى بطلب المسمار المجوف واعتماد التبريد والتشحيم القسري. حافظ على بيئة العمل نظيفة ولا تدع الغبار والشوائب الأخرى تدخل مجرى السباق أو الصمولة. إذا لم يكن الوضع جيدًا ، ففكر في إضافة غطاء واقي للمسامير.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①كفاءة نقل عالية. كفاءة النقل لنقل اللولب الكروي بشكل عام 20.92-10 بالمائة ، وكفاءة نقل ناقل الحركة اللولبي العادي هو 20.20-0.40.
②دقة نقل عالية وحركة مستقرة ولا توجد ظاهرة زحف. محرك الكرة اللولبية هو في الأساس احتكاك متداول ، مع مقاومة احتكاك صغيرة ، ومقاومة الاحتكاك لا علاقة لها بسرعة الحركة.
③يعمل في الاتجاه المعاكس دون التباطؤ. بعد - إحكام ربط البرغي الكروي والصمولة ، يمكن التخلص من الخلوص المحوري. بهذه الطريقة ، لا توجد منطقة ميتة في الاتجاه المعاكس ، ويتم تحسين دقة وصلابة ناقل الحركة المحوري.
④إنه قابل للعكس. نظرًا لأن فقدان الاحتكاك في اللولب الكروي صغير ، فيمكن تحويله من حركة دورانية إلى حركة خطية ، ويمكن أيضًا تحويله من حركة خطية إلى حركة دورانية. يمكن استخدام كل من المسمار اللولبي والجوز كمحرك أو تابع.
⑤عمر خدمة طويل. نظرًا لفقدان الاحتكاك الصغير الناتج عن الاحتكاك المتداول ، فإن عمر الخدمة طويل.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
اتصل الآن
E-mail: sales@gyballscrew.com Tel(ال WhatsApp): بالإضافة إلى 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
